How to Measure a Broken Part So It Can Be Reprinted
What to measure on a broken knob, clip or bracket, which tools you need, and how to photograph it so it can be redrawn and printed to fit first time.

The short answer
Measure with digital callipers to a tenth of a millimetre: the overall length, width and height, every hole's diameter, the distance between hole centres, and the thickness of the walls. Then measure the part it fits into, because a worn or broken piece misleads. Send the numbers with square-on photos of each face, a ruler in frame, and the part can be redrawn and printed.
A broken plastic part is usually simple to redraw. What decides whether the reprint fits first time is not the drawing; it is the measurements that came with it. This is the checklist we would follow ourselves.
What you need
- Digital callipers. A basic pair from a hardware shop reads to 0.1 mm, which is enough for almost any household part.
- A steel ruler, for photos and for anything longer than the callipers open.
- Your phone camera.
- Paper and a pen, to sketch the part and write numbers on it as you go.
A ruler alone can work for a simple part with no holes or fits, but for anything that slots, clips or screws into something else, callipers are worth the small cost.
Before you measure
- Collect every broken piece. A fragment that looks useless often holds the one dimension that matters.
- Clean off grease and dust, which add to every reading.
- Tape the pieces together if you can, so you can measure across the break.
- Decide what the part does: does it carry weight, turn, slide or snap? That tells you which measurements must be exact.
The measurements that matter
| Feature | What to measure | Tip |
|---|---|---|
| Overall size | Length, width and height at the widest points | Close the callipers gently; squeezing plastic shrinks the reading. |
| Holes | Inside diameter, and depth if it is blind | Use the small inner jaws. Measure in two directions; a worn hole goes oval. |
| Hole positions | Centre to centre, and centre to the nearest edge | Measure edge to edge, then add one hole's diameter to get centre to centre. |
| Pins and shafts | Outside diameter and length | On a D-shaped shaft, measure the round side and the flat side separately. |
| Walls | Thickness at several points | Note the thinnest point. If it broke there, the reprint can be made thicker. |
| Clips and tabs | Length, thickness, and the height of the hook | These snap off most. Measure the slot they go into as well. |
| Angles | Whether faces are square or sloped | A phone photo taken straight on is usually enough for us to read the angle. |
Measure the other half too
The part that broke has been worn, bent or stressed, so its numbers can lie. The part it fits into usually has not. If a knob goes on a shaft, measure the shaft. If a clip goes into a slot, measure the slot. If a bracket screws to a cabinet, measure the screw holes in the cabinet and the screw itself. Those numbers set the fit; the broken piece mostly tells us the shape.
This matters because a printed part needs a small, deliberate gap to fit something else. Draw a hole at exactly the size of the shaft and it will not go on. We add that gap when we redraw, but only if we know what the part is mating with. Tolerances, threads and fits explains why.
Threads and screws
For a threaded part, measure the outside diameter of the screw or bolt, and count how many threads there are over 10 mm of its length. Better still, send the screw itself in a photo next to a ruler, or tell us the size printed on its packet. Printed threads suit caps and lids turned by hand. Anywhere a screw will be tightened often, a brass insert is the better design.
How to photograph it
- One photo of each face, taken straight on rather than at an angle.
- A ruler lying flat beside the part, at the same height as the face you are photographing.
- Good daylight, on a plain background that contrasts with the part.
- A photo of the part in place, or where it used to sit, so we can see how it works.
- Close-ups of the break, and of any clip, hook or hole.
Sketch it and write the numbers on
A rough pen sketch with every measurement written beside the feature it belongs to is worth more than a page of numbers in a list. Mark which ones must be exact (the shaft hole, the screw spacing) and which ones only need to look right (the outer curve). Photograph the sketch and send it with the rest.
What happens next
Send the photos, sketch and numbers through custom projects. The form takes up to four photos, and the rest can follow on WhatsApp. We message you within 24 hours to talk it through, then you get one firm price for design, printing and delivery before anything starts. Simple parts are modelled at no extra charge.
Not every part should be reprinted. Anything that holds heavy weight overhead, sits against high heat or seals water under pressure is the wrong job for plastic, as what 3D printing cannot do explains. For everything else, see replacement parts you can print instead of importing.
Frequently asked questions
What measurements do I need to reprint a broken part?
Overall length, width and height; the diameter of every hole and pin; the distance between hole centres; and the wall thickness. Measure the part it fits into as well, because the broken piece may be worn. Add straight-on photos with a ruler in frame.
Do I need callipers to measure a part for 3D printing?
For anything that fits onto a shaft, into a slot or around a screw, yes. Basic digital callipers read to 0.1 mm and are cheap at hardware shops. A ruler can do for a simple shape with no fits.
Can you make a replacement part from photos only?
Photos show the shape but not the exact size, so measurements are still needed for anything that has to fit. A ruler in every photo helps, and the critical numbers should be measured directly.
What if the reprinted part does not fit?
Tell us which dimension is wrong and by how much, and it is adjusted and reprinted. Sending the measurements of the mating part from the start is what avoids this.
How much does it cost to reprint a broken part in Lebanon?
Most small replacement parts cost $13 to $25 delivered on 3DprintLB. Simple parts are modelled from your measurements at no extra charge, and you get one firm price before any work starts.
Got a file to print?
Instant price, delivered anywhere in Lebanon for a flat $5.


